[strongSwan] S2S VPN with dynamic DNS

[Dusan Ilic]

The selector on both sides is the other sides  dynamic domain name. 

---- Noel Kuntze skrev ----

>What's the selector for the PSK?
>
>On 27.06.2017 00:25, Dusan Ilic wrote:
>> Yep, the hostname are resolving to the right IP. Obviously Fortigate implementation has no problems reconnecting, though Strongswan has.
>> 
>> 
>> Den 2017-06-27 kl. 00:10, skrev Noel Kuntze:
>>> "Strongswan won't connect even manually." What does that mean?
>>> No secret found? Is the IP correct?
>>>
>>> On 27.06.2017 00:05, Dusan Ilic wrote:
>>>> Anyone...?
>>>> I had to reboot the remote Strongswan gateway a couple of hours later, then it came back up again.
>>>>
>>>>
>>>> Den 2017-06-19 kl. 08:51, skrev Dusan Ilic:
>>>>> Yet again, the fortigate router reconnected to Strongswan on it's own without manual intervention 12 minutes after the other sides public IP changed... Strongswan won't connect even manually.
>>>>>
>>>>>
>>>>> Den 2017-06-19 kl. 08:47, skrev Dusan Ilic:
>>>>>> Okey, today it happened again, new IP on one end of tunnel and updated in DNS. Pinging the new IP from both sides shows it resolves correctly, restarting Strongswan on both sides and the same issue as before. (last time it started to work on the evening same day)
>>>>>>
>>>>>> generating IKE_SA_INIT request 0 [ SA KE No N(NATD_S_IP) N(NATD_D_IP) ]
>>>>>> sending packet: from 94.254.123.x[500] to 85.24.244.x[500]
>>>>>> received packet: from 85.24.244.x[500] to 94.254.123.x[500]
>>>>>> parsed IKE_SA_INIT response 0 [ SA KE No N(NATD_S_IP) N(NATD_D_IP) CERTREQ N(MULT_AUTH) ]
>>>>>> received 1 cert requests for an unknown ca
>>>>>> authentication of 'hostname' (myself) with pre-shared key
>>>>>> no shared key found for 'hostname' - '85.24.244.x'
>>>>>>
>>>>>> Why isn't it working?
>>>>>> What does the message "no shared key found for 'hostname' - '85.24.244.x'" mean?
>>>>>> This time the IP is correct and updated.
>>>>>>
>>>>>>
>>>>>> Den 2017-06-14 kl. 15:23, skrev Dusan Ilic:
>>>>>>> Hi,
>>>>>>>
>>>>>>> I have a S2S IPsec tunnel setup that have problems now when one side of the tunnel have been assigned a new public IP. The hostname used have been immediately updated by way od dynamic DNS, and the TTL have expired two hours ago. When trying to up the tunnel on the side with the changed IP, Strongswan returns "received AUTHENTICATION_FAILED notify error", and when trying to do the same on the remote end the log looks like following.
>>>>>>>
>>>>>>> generating IKE_SA_INIT request 0 [ SA KE No N(NATD_S_IP) N(NATD_D_IP) ]
>>>>>>> sending packet: from 94.254.123.x[500] to 85.24.242.x[500]
>>>>>>> received packet: from 85.24.242.x[500] to 94.254.123.x[500]
>>>>>>> parsed IKE_SA_INIT response 0 [ SA KE No N(NATD_S_IP) N(NATD_D_IP) CERTREQ N(MULT_AUTH) ]
>>>>>>> received 1 cert requests for an unknown ca
>>>>>>> authentication of 'hostname' (myself) with pre-shared key
>>>>>>> no shared key found for 'hostname' - '*85.24.240.x*'
>>>>>>>
>>>>>>> Now as you can see the packets are sent to the correct host (domain is correctly resolved), however on the last line it's the old IP. What's happening here? I have tried restartin Strongswan on both hosts, but it doesn't help.
>>>>>>>
>>>>>>> This is the first time since I setup the tunnel with dynamic DNS that one side of the tunnel have changed IP, how can I make either side of the tunnel to continue reconnecting until the hostname is properly resolving again?
>>>>>>> I have another tunnel going to the same client, and it have succesfully reconnected again after it picked up the new IP. The client is a Fortigate router. So, how can I force Strongswan to retry ?
>>>>>>>
>> 
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.strongswan.org/pipermail/users/attachments/20170627/a2746907/attachment-0001.html>