[strongSwan] FW: payload of type AUTH more than 1 times (2) occurred in current message

[Alexis Salinas]

here are the attachment
________________________________________
From: Alexis Salinas
Sent: July 14, 2015 12:05
To: Andreas Steffen
Subject: RE: [strongSwan] payload of type AUTH more than 1 times (2) occurred in current message

Thanks for the reply Andreas.

That is what I thought too, but I was wondering if that was allowed. So, thank you  for the strong clarification.

Do you know if this was allowed in IKEv1 and perhaps these guys just re-use part of their code?

As per your request, here are 2 files. One with ike=3 enabled, which didn't show much more detail around the error. On the second fiIe I also enable enc=2 in case that is more useful (you can see the parsing and verification of the message)

Let me know if you need anything else.

Cheers,
Alexis.

________________________________________
From: Andreas Steffen [andreas.steffen at strongswan.org]
Sent: July 14, 2015 03:12
To: Alexis Salinas; users at lists.strongswan.org
Subject: Re: [strongSwan] payload of type AUTH more than 1 times (2) occurred in current message

Hi Alexis,

it looks as if the 3rd party VPN client sends two AUTH payloads in its
IKE_AUTH request. This does not conform with the IKEv2 RFC. Could you
send me a strongSwan log file with the log level set to

  charondebug="ike 3"

in ipsec.conf.

Best regards

Andreas

On 07/13/2015 09:23 PM, Alexis Salinas wrote:
> Hello All,
> I'm testing strongSwan as a VPN gateway for a 3rd party VPN client.  PSK and certificate authentication works fine, but when testing EAP-TLS and I get this error message on the strongSwan side, after the EAP authentication succeeds.
>
> Jul 10 16:42:11 debian-vm1-alexis charon: 14[ENC] payload of type AUTH more than 1 times (2) occurred in current message
> Jul 10 16:42:11 debian-vm1-alexis charon: 14[IKE] message verification failed
>
> See attachment for full  logs.
>
> Here is my strongSwan configuration:
>
> # ipsec.conf - strongSwan IPsec configuration file
>
> config setup
>       # strictcrlpolicy=yes
>       # uniqueids = no
>
> conn %default
>       ikelifetime=60m
>       keylife=20m
>       rekeymargin=3m
>       keyingtries=1
>       keyexchange=ikev2
>
> conn rw-eap-tls
>         left=10.1.65.147
>       leftid=ocm at test.org
>         leftsubnet=10.99.0.0/24
>       leftcert=ocmCert.pem
>       leftauth=pubkey
>       leftfirewall=yes
>       rightsourceip=172.22.0.0/24
>       rightauth=eap-radius
>       rightsendcert=never
>       right=%any
>       auto=add
>       eap_identity=%identity
>
> Does any of you know what this is about?
>
> what is strongSwan expecting at this point? Looking at the RFC [1] there should be a message type AUTH (message 7).
>
> I can enable more logging if needed.
>
> Thanks.
> Alexis.
>
>
>
> [1] : https://tools.ietf.org/html/rfc7296#section-2.16
>
>
>
>
> _______________________________________________
> Users mailing list
> Users at lists.strongswan.org
> https://lists.strongswan.org/mailman/listinfo/users
>

--
======================================================================
Andreas Steffen                         andreas.steffen at strongswan.org
strongSwan - the Open Source VPN Solution!          www.strongswan.org
Institute for Internet Technologies and Applications
University of Applied Sciences Rapperswil
CH-8640 Rapperswil (Switzerland)
===========================================================[ITA-HSR]==
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: strongswan-logs-ike3.txt
URL: <http://lists.strongswan.org/pipermail/users/attachments/20150720/cf9e5fde/attachment-0002.txt>
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: strongswan-logs-ike3-enc2.txt
URL: <http://lists.strongswan.org/pipermail/users/attachments/20150720/cf9e5fde/attachment-0003.txt>