[strongSwan] Traffic Pauses to IKEv1 VPN with Juniper ISG 1000

Sun Dec 13 22:52:09 CET 2015

On 12/13/2015 09:50 PM, Mahesh Neelakanta wrote:
> Thanks Thomas. I was able to run the "ip" command but it does look like (as
> you mentioned) that CONFIG_XFRM_STATISTICS is disabled (this is the amazon
> ubuntu 12.04 AMI). I'll try a newer release of amazon's own linux to see if
> it has it installed before trying a kernel recompile.
The kernel option is marked experimental. I doubt, any distro will have
enabled it.
> Right now the ip
> command shows no errors (but i've restarted vpn) so i'll await it to hang
> again.
> 
> ip -s x s s spi 0xc6ff382c
> 
>         proto esp spi 0xc6ff382c(3338614828) reqid 2(0x00000002) mode tunnel
>         replay-window 32 seq 0x00000000 flag af-unspec (0x00100000)
>         auth-trunc hmac(sha1) 0xc609a31c3e5b7d6fa5267737c759fed017d2d6ea
> (160 bits) 96
>         enc cbc(aes) 0x4fba8977e230c1155780f03a19b90111 (128 bits)
Mahesh you posted your keys! That's awful! It enables anyone who
recorded your traffic to easily decrypt it. Reestablish the SA *as*
*soon* *as* *possible*!
>         lifetime config:
>           limit: soft (INF)(bytes), hard (INF)(bytes)
>           limit: soft (INF)(packets), hard (INF)(packets)
>           expire add: soft 3600(sec), hard 3600(sec)
>           expire use: soft 0(sec), hard 0(sec)
>         lifetime current:
>           183887577(bytes), 191174(packets)
>           add 2015-12-13 20:39:21 use 2015-12-13 20:39:21
> *        stats:*
> *          replay-window 0 replay 0 failed 0*
Stats look fine. You should however check the settings when the error
you mentioned occurs!

Cheers,

Thomas
> 
> On Sun, Dec 13, 2015 at 3:23 PM, Thomas Egerer <hakke_007 at gmx.de> wrote:
> 
>> Mahesh,
>>
>> run 'ip -s x s s spi <your_broken_inbound_spi' (as root) on your
>> Linux-Box and check if your error statistics increase for the particular :
>> <snip>
>>         stats:
>>           replay-window 0 replay 0 failed 0
>> <snap>
>> Also: 'grep -vw 0 /proc/net/xfrm_stat' and check for increasing
>> counters. You will probably have to rebuild your Linux-kernel for this,
>> unless it has the CONFIG_XFRM_STATISTICS option enabled. If the file
>> does exist you're lucky, if not -- like on current Debian systems -- you
>> will have to recompile.
>> The rationale behind this is that your inbound traffic gets dropped
>> during inbound transformation. Reasons for this may vary: failed
>> integrity checks, replay problems, failed inbound policy check etc.
>>
>> Cheers,
>> Thomas
>>
>>
>> On 12/13/2015 05:06 PM, Mahesh Neelakanta wrote:
>>> Hi,
>>>  I  have a Strongswan VPN server that is being used to terminate VPN
>>> connections with multiple endpoints. Most of the existing endpoints are
>>> cisco, sophos, etc. Recently I have a Juniper ISG 1000 endpoint that is
>>> posing some intermittent traffic problems.
>>>
>>> The exact issue is that traffic over the VPN pauses after some (random)
>>> time. The tunnel itself is up and at the next rekey traffic starts
>> flowing
>>> again. If I reduce the re-key time from 3600s down to 600s, the problem
>> is
>>> reduced significantly. I did verify with the remote side that their
>> keylife
>>> is 3600s. We do not have DPD enabled. There is constant traffic so there
>>> are no periods of inactivity.
>>>
>>> During the periods where traffic pauses, ipsec statusall report shows no
>>> more packets in bytes_i (whereas bytes_o is still increasing).
>>>
>>> Here is the config on our end (IPs and subnets have been changed for
>>> security):
>>>
>>> config setup
>>>    uniqueids = no
>>>    charondebug = ike 2
>>>
>>> conn %default
>>>    keyingtries=%forever
>>>    dpdaction=none
>>>
>>> conn vpn-juniper-prd
>>>         left=%defaultroute
>>>         leftid=42.75.5.14 # Our actual local IP is  10.20.1.18, we are
>>> NATed going out
>>>         leftsubnet=5.22.11.21/32
>>>         right=168.42.68.5
>>>         rightid=168.42.68.5
>>>         rightsubnet=12.23.0.0/16
>>>         keyexchange=ikev1
>>>         ikelifetime=28800s
>>>         ike=aes128-sha1-modp1024
>>>         esp=aes128-sha1-modp1024
>>>         keylife=3600m
>>>         type=tunnel
>>>         compress=no
>>>         authby=secret
>>>         auto=start
>>>
>>> Notice that the last "bytes_i" shows 145s ago (ipsec statusall output):
>>>
>>> vpn-juniper-prd:  %any...168.42.68.5  IKEv1
>>> vpn-juniper-prd:   local:  [42.75.5.14] uses pre-shared key
>> authentication
>>> vpn-juniper-prd:   remote: [168.42.68.5] uses pre-shared key
>> authentication
>>> vpn-juniper-prd:   child:  5.22.11.21/32 === 12.23.0.0/16 TUNNEL
>>> vpn-juniper-prd[1]: ESTABLISHED 110 minutes ago,
>>> 10.20.1.18[42.75.5.14]...168.42.68.5[168.42.68.5]
>>> vpn-juniper-prd[1]: IKEv1 SPIs: a8ed9dd3b567a578_i* 97dbd6dbb3683aa4_r,
>>> pre-shared key reauthentication in 5 hours
>>> vpn-juniper-prd[1]: IKE proposal:
>>> AES_CBC_128/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024
>>> vpn-juniper-prd{44}:  REKEYED, TUNNEL, reqid 4, expires in 10 minutes
>>> vpn-juniper-prd{44}:   5.22.11.21/32 === 12.23.0.0/16
>>> vpn-juniper-prd{52}:  INSTALLED, TUNNEL, reqid 4, ESP SPIs: c3fdc693_i
>>> 9d90fe7f_o
>>> vpn-juniper-prd{52}:  AES_CBC_128/HMAC_SHA1_96, 24197112 bytes_i *(26366
>>> pkts, 145s ago*), 8889197 bytes_o (31780 pkts, 0s ago), rekeying in 10
>>> minutes
>>> vpn-juniper-prd{52}:   5.22.11.21/32 === 12.23.0.0/16
>>>
>>> During that time, we still see packets going in/out via the eth0
>> interface :
>>>
>>> 03:38:52.349565 IP 10.20.1.18 > 168.42.68.5:
>>> ESP(spi=0x9d90fe7f,seq=0x7c0f), length 132
>>> 03:38:52.363916 IP 168.42.68.5 > 10.20.1.18:
>>> ESP(spi=0xc3fdc693,seq=0x5cd3), length 132
>>> 03:38:52.548261 IP 168.42.68.5 > 10.20.1.18:
>>> ESP(spi=0xc3fdc693,seq=0x5cd4), length 100
>>> 03:38:52.564198 IP 168.42.68.5 > 10.20.1.18:
>>> ESP(spi=0xc3fdc693,seq=0x5cd5), length 100
>>> 03:38:53.357693 IP 10.20.1.18 > 168.42.68.5:
>>> ESP(spi=0x9d90fe7f,seq=0x7c10), length 132
>>> 03:38:53.371666 IP 168.42.68.5 > 10.20.1.18:
>>> ESP(spi=0xc3fdc693,seq=0x5cd6), length 132
>>> 03:38:54.365616 IP 10.20.1.18 > 168.42.68.5:
>>> ESP(spi=0x9d90fe7f,seq=0x7c11), length 132
>>> 03:38:54.379533 IP 168.42.68.5 > 10.20.1.18:
>>> ESP(spi=0xc3fdc693,seq=0x5cd7), length 132
>>> 03:38:55.250707 IP 168.42.68.5 > 10.20.1.18:
>>> ESP(spi=0xc3fdc693,seq=0x5cd8), length 100
>>> 03:38:55.373593 IP 10.20.1.18 > 168.42.68.5:
>>> ESP(spi=0x9d90fe7f,seq=0x7c12), length 132
>>> 03:38:55.387695 IP 168.42.68.5 > 10.20.1.18:
>>> ESP(spi=0xc3fdc693,seq=0x5cd9), length 132
>>>
>>>
>>> thanks,
>>> mahesh
>>>
>>>
>>>
>>> _______________________________________________
>>> Users mailing list
>>> Users at lists.strongswan.org
>>> https://lists.strongswan.org/mailman/listinfo/users
>>>
>>
>>
>>
>> _______________________________________________
>> Users mailing list
>> Users at lists.strongswan.org
>> https://lists.strongswan.org/mailman/listinfo/users
>>
> 


-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: OpenPGP digital signature
URL: <http://lists.strongswan.org/pipermail/users/attachments/20151213/f13e61c9/attachment-0001.pgp>